do not scale from this print 0.80 typ .031 "f" 1.40 ref .055 0.80 .031 ref "a" "a" 02 (see note 4) 01 (see note 4) lsem-20-01-dh-a wt-50-t pin n 5.13 ref .202 2.45 .096 4.15 ref .163 7.80 ref .307 0.25 ref .010 0.10[.004] "g" ref designed & dimensioned in millimeters[inches] c 1.32 ref .052 0.20 (typ) .008 ref 3.65 .144 ref (no of positions x .80[.031]) -.80[.031] 1.10 ref .043 1.32 ref .052 4.80 .189 ref "j" fig.1 lsem-120-01-xx-dh-a-x-x shown 0.866 0.10 .034 .004 1.05 ref .041 1.12 ref .044 0.670 0.10 .026 .004 1.45 .057 4.23 .167 0.50 .020 ref section "a"-"a" c c *= not released for production lsem-1xx-xx-x-dh-a-x-x-tr no of positions -20, -30, -40, -50 tail option -dh: dual horizontal lead style -01: plating specification -l: 10u"(0.25u"m)gold (matte tin tails) -f: gold flash (matte tin tails) packaging -tr: tape & reel (see note 6) shield * -s: with shield (see sht 2, fig.2) -n: no shield option -k: polyimide film (see sht 2, fig.3) (use k-500-300) option -a: alignment pin c c c c c sheet of unless otherwise specified, dimensions are in millimeters[inches]. tolerances are: decimals angles x.x: 0.3 [.01] 2 x.xx: 0.13 [.005] x.xxx: 0.051 [.0020] material: 0.8mm hermaphroditic horizontal for lsem -dh by: lsem-1xx-xx-x-dh-a-x-x-tr dwg. no. description: proprietary note this document contains information confidential and proprietary to samtec, inc. and shall not be reproduced or transferred to other documents or disclosed to others or used for any purpose other than that which it was obtained without the expressed written consent of samtec, inc. do not scale drawing chadp 04/08/2009 3 1 sheet scale: 1:0.2 insulator: black lcd contact or terminal: phos bronze shield: stainless steel weld tab: copper f:\dwg\misc\mktg\lsem-1xx-xx-x-dh-a-x-x-tr-mkt.slddrw 520 park east blvd, new albany, in 47150 phone: 812-944-6733 fax: 812-948-5047 fromparent+phone: 812-944-6733 fax: 812-948-5047 notes: 1. represents a critical dimension. 2. burr allowance: .038[.0015] . 3. minimum pushout force: 2.22 n [.5 lbs]. 4. when mating with another lsem-dh, 01 will mate with contact 02 on mating connector when mating with a lsem-dv, pin 01 will mate with pin n, where n = total number of positions. 5. measure from top of vertical wall. 6. for quantities up to 49 pcs., no leader , trailer or reel will be supplied. for quantities of 50-124 pcs., no leader or trailer will be supplied. revision b
"h" ref 4.98 ref .196 "b" "b" 2.75 .108 ref 0.80 .031 ref sh40-01-dh-n c 0.10[0.004] 1.32 ref .052 "j" ref 1.95 ref .077 1.32 ref .052 1.10 ref .043 "k" 5.50 .217 "l" 0.90 .035 *fig. 3 -k kapton option lsem-120-01-xx-dh-a-s-k shown (same as fig.1 different as shown) (*= not released for production) c c 0.13 .005 ref shield option lsem-120-01-xx-dh-a-s-x shown (same as fig.1 different as shown) (*= not released for production) *fig. 2 sheet of 0.8mm hermaphroditic horizontal for lsem -dh by: lsem-1xx-xx-x-dh-a-x-x-tr dwg. no. description: proprietary note this document contains information confidential and proprietary to samtec, inc. and shall not be reproduced or transferred to other documents or disclosed to others or used for any purpose other than that which it was obtained without the expressed written consent of samtec, inc. do not scale drawing chadp 04/08/2009 3 2 sheet scale: 1:0.2 f:\dwg\misc\mktg\lsem-1xx-xx-x-dh-a-x-x-tr-mkt.slddrw 520 park east blvd, new albany, in 47150 phone: 812-944-6733 fax: 812-948-5047 fromparent+phone: 812-944-6733 fax: 812-948-5047 revision b
"c" "c" fig. 4 (in process 1) 0.150 .006 6.30 0.08 .248 .003 section "c"-"c" c-261-02-x c c c 0.10[0.004] "e" "e" fig. 5 (in process 2) section "e"-"e" scale 4 : 1 must latch into body lsem-xx-dh c "d" "d" fig. 6 (in process 3) 9.00 0.08 .354 .003 0.08 max .003 bottom row section "d"-"d" scale 4 : 1 c-261-03-x c c 0.10[0.004] c sheet of 0.8mm hermaphroditic horizontal for lsem -dh by: lsem-1xx-xx-x-dh-a-x-x-tr dwg. no. description: proprietary note this document contains information confidential and proprietary to samtec, inc. and shall not be reproduced or transferred to other documents or disclosed to others or used for any purpose other than that which it was obtained without the expressed written consent of samtec, inc. do not scale drawing chadp 04/08/2009 3 3 sheet scale: 5:1 f:\dwg\misc\mktg\lsem-1xx-xx-x-dh-a-x-x-tr-mkt.slddrw 520 park east blvd, new albany, in 47150 phone: 812-944-6733 fax: 812-948-5047 fromparent+phone: 812-944-6733 fax: 812-948-5047 revision b
|
